Clothes hanger manufacturer introduces the installation of smart clothes drying rack
Release Time:
Sep 27,2022
The manufacturer of clothes hangers introduces that the smart clothes hanger is an integrated multifunctional smart clothes hanger improved on the basis of the traditional hand-cranked clothes hanger. Through the on-off control of the circuit board I/O port and the forward and reverse rotation of the motor, the functions of lighting, sterilization, air drying, drying, voice control, etc. are realized, so as to achieve the function of lifting and lowering the clothes rod. The on-chip system control that stops when encountering obstacles allows intelligence and safety to be integrated into modern life. For the health and comfort of the family, the emergence and rapid development of smart clothes hangers have been promoted.
The manufacturer of clothes hangers introduces that the smart clothes hanger is an integrated multifunctional smart clothes hanger improved on the basis of the traditional hand-cranked clothes hanger. Through the on-off control of the circuit board I/O port and the forward and reverse rotation of the motor, the functions of lighting, sterilization, air drying, drying, voice control, etc. are realized, so as to achieve the function of lifting and lowering the clothes rod. The on-chip system control that stops when encountering obstacles allows intelligence and safety to be integrated into modern life. For the health and comfort of the family, the emergence and rapid development of smart clothes hangers have been promoted.
1. Instructions
1. Prepare to install the smart clothes hanger.
1. Make sure that the power cord is reserved at both ends of the installation location, and the power supply needs to have a ground wire.
2. Make sure the power is turned off during installation, and the input voltage is between 180-220V 50Hz.
3. If the power cord is only one section, the power cord needs to be led out for a certain length. The distance between the two holes is the length of the clothes hanger.
4. Prepare installation tools such as tape measure, marker, drill, etc.
2. The manufacturer of the clothes hanger explains the measurement position and drilling holes with an electric drill
Then measure the installation position, first measure the length of the smart electric clothes hanger, determine the installation position of the fixings at both ends according to the length of the smart electric clothes hanger, then measure the width of the balcony and mark it, the middle of the cross is the installation position of the fixings, and then drill holes at the marked position.
3. Install the fixings
Assemble the fasteners and expansion screws, and then install the fasteners on both sides with an electric drill.
4. The manufacturer of the clothes hanger introduces the installation of the smart electric clothes hanger box
There is a rectangular interface connected to the fixing device on both sides of the box of the smart electric clothes hanger. Clamp the two interfaces, install the clips on both sides, and then fix the clothes hanger box to the clamp door with screws.
5. Install the bracket group
For the fixing bolts used in the bracket, just connect and fix the folding arm with the fixing bolts. On the other side, fix the fixing bolts to the connection holes of the folding arm. After installing the fixing bolts, pass the wire rope through the hanging bolt holes. Then tighten it with the hanger screw, and do the same on the other side. Pass the wire rope through the hanger hole and tighten it with the hanger screw.
Sixth, connect the power supply
Be careful not to connect it wrongly when connecting the power supply. Generally, when the power supply is successfully connected, the clothes drying rack will make a "beep" sound, indicating that the connection is successful.
Seventh, connect the drying rod
1. Assemble the drying rod accessories, put the drying rod into the half rings at both ends of the lifting frame, put the drying rod into the rings at both ends of the lifting frame, clamp the drying rod with a pipe clamp and install the pipe clamp screws.
Eighth, adjust the drying rod
Use a tape measure to adjust the distance between the four corners, keep the hanger vertical, and facilitate the hanger to lift smoothly. After adjustment, you can tighten the screws to fix it, and finally trim off the excess wire rope.
Messages
We will contact you within one working day. Please pay attention to your email.
Quick Link
HUAHAI HOUSEWARES
Contact
Tel: +86 773-7235826
E-mail: cgx@glhuahai.com
Company address: Yonghua lndustrialzone,Qingshan, Lipu Countg, Guilin City
